Serviceline Industrial Sensors
Serviceline Explosion Protection
Explosion Protection

Temperature Converter S1SD-1TI-1U

S1SD-1TI-1U
  • 1-channel signal conditioner
  • 24 V DC supply
  • Thermocouple, RTD, potentiometer or mV input
  • Input for PTC thermistor
  • Current and voltage output
  • Line fault (LFD) and sensor burnout detection
  • Accuracy 0.1 %
  • Connection via screw terminals

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Datasheet excerpt: Technical data of  S1SD-1TI-1U

General specifications
Signal typeAnalog input
Operation timeMTBF: 353 a acc. to SN 29500
stationary continuous operating, average ambient temperature 40 °C (104 °F)
Supply
ConnectionPower Bus or terminals 1-, 2+
Rated voltage16.8 ... 31.2 V DC
Power dissipation0.7 W
Power consumption0.8 W
Interface
Programming interfaceprogramming socket
Input
Connection sidefield side
Connectionterminals 5, 6, 7, 8
PTCtype KT, KTY, ST
Measuring currentapprox. 200 µA
Types of measuring2-, 3-, 4-wire connection
Lead resistance≤ 100 Ω per line
Measurement loop monitoringsensor breakage, lead breakage, short circuit
RTDtype Pt100, Pt200, Pt500, Pt1000 (EN 60751:1995)
type Ni100, Ni200, Ni500, Ni1000 (DIN 43760)
Measuring currentapprox. 200 µA
Types of measuring2-, 3-, 4-wire connection
Lead resistancemax. 100 Ω per line
Measurement loop monitoringsensor breakage, lead breakage, short circuit
Thermocouplestype B, E, J, K, N, S, T (IEC 584-1:1995)
type L, U (DIN 43710:1985)
type C, D (ASTM E988)
Cold junction compensationexternal (Pt100) and internal , manually
Lead resistancemax. 10 kΩ
Measurement loop monitoringsensor breakage, lead breakage
Resistor
Measurement range0 ... 5 kΩ
Potentiometer0.2 ... 50 kΩ
Types of measuring3-wire connection
Voltage-100 ... 100 mV
-1000 ... 1000 mV
Input resistance≥ 1 MΩ
Output
Connection sidecontrol side
Connectionterminals 3-, 4+
Analog voltage output0/1 ... 5 V , 0/2 ... 10 V , load ≥ 2 kΩ
Analog current output0/2 ... 10 mA, 0/4 ... 20 mA, load ≤ 600 Ω
Ripple≤ 10 mV eff
Fault signaldownscale or upscale
Transfer characteristics
Accuracymax. 0.1 % of full-scale value
Measuring time≤ 300 ms
Deviation
RTD< 0.1 K/0.05 % of the measured value
Thermocouples< 0.3 K/0.1 % of the measured value
Voltage< 0.1 % of the measured value
Potentiometer< 0.02 % of the measured value
Influence of ambient temperature< 100 ppm/K of full-scale value
Galvanic isolation
Output/power supplysafe electrical isolation by reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff test voltage 3 kV, 50 Hz, 1 min
Input/Other circuitssafe electrical isolation by reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff test voltage 3 kV, 50 Hz, 1 min
Indicators/settings
Control elementsDIP switch
keys
Configurationvia DIP switches
via keys
via software
Labelingspace for labeling at the front
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EUEN 61326-1:2013 (industrial locations)
Conformity
Degree of protectionIEC 60529:2001
Protection against electrical shockEN 61010-1:2010
Ambient conditions
Ambient temperature-25 ... 70 °C (-13 ... 158 °F)
Storage temperature-40 ... 85 °C (-40 ... 185 °F)
Damaging gasdesigned for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Degree of protectionIP20
Connectionscrew terminals
Core cross section0.5 ... 2.5 mm2 (20 ... 14 AWG)
Massapprox. 70 g
Dimensions6.2 x 97 x 107 mm (0.24 x 3.82 x 4.21 inch) (W x H x D) , housing type S1
Height97 mm
Width6.2 mm
Depth107 mm
Mountingon 35 mm DIN mounting rail acc. to EN 60715:2001
Data for application in connection with hazardous areas
CertificateDEMKO 16 ATEX 1750X
MarkingEx-Hexagon II 3G Ex nA IIC T4 Gc
Directive conformity
Directive 2014/34/EUEN 60079-0:2012+A11:2013 , EN 60079-15:2010
International approvals
UL approvalE106378
IECEx approval
IECEx certificateIECEx UL 16.0116X
IECEx markingEx nA IIC T4 Gc
General information
Supplementary informationObserve the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

Classifications

SystemClasscode
ECLASS 13.027210129
ECLASS 12.027210129
ECLASS 11.027210129
ECLASS 10.0.127210129
ECLASS 9.027210129
ECLASS 8.027210190
ECLASS 5.127210107
ETIM 9.0EC002919
ETIM 8.0EC002919
ETIM 7.0EC002919
ETIM 6.0EC002919
ETIM 5.0EC001485
UNSPSC 12.132101514

Details: S1SD-1TI-1U

This signal conditioner provides the galvanic isolation between field circuits and control circuits.

The device has an input for signals of the following field devices:
- resistance thermometers
- thermocouples
- PTC thermistors
- potentiometers
- voltage sources
- field device with its own characteristic

The device provides the following standard signals at the output:
- 0/2 mA ... 10 mA signal
- 0/4 mA ... 20 mA signal
- 0/1 V ... 5 V signal
- 0/2 V ... 10 V signal

This device has an integrated cold junction compensation. You can also implement external cold junction compensation.

A fault is signalized by LEDs.

The device is easily configured by the use of DIP switches.

The Teach-In function can be used to teach in the potentiometer start value and end value.

The device can be powered via terminals or Power Bus.

Datasheet: S1SD-1TI-1U

DatasheetFile TypeFile Size
Datasheet S1SD-1TI-1UPDF977 KB
Fiche de données S1SD-1TI-1UPDF1021 KB
Datenblatt S1SD-1TI-1UPDF996 KB
Datasheet S1SD-1TI-1UPDF1185 KB
Hoja de datos S1SD-1TI-1UPDF1037 KB

Documents: S1SD-1TI-1U

BrochuresFile TypeFile Size
Product Overview SC-SystemPDF456 KB
Productübersicht SC-SystemPDF488 KB
Instruction manuals
Návod k poużitíPDF132 KB
Instruktions manualPDF0 KB
Instruction manualPDF136 KB
KasutusjuhendPDF127 KB
KäyttöohjePDF127 KB
Manuel d'instructionsPDF138 KB
BetriebsanleitungPDF137 KB
Οδηγίες χρήσηςPDF141 KB
HandleidingPDF0 KB
Instruction manual / BetriebsanleitungPDF130 KB
Manuale di istruzioniPDF135 KB
Lietošanas pamācībaPDF131 KB
Instrukciju vadovasPDF0 KB
Instrukcja obsługiPDF134 KB
Manual de instruçõesPDF132 KB
Manual de utilizarePDF0 KB
Návod na poużitiePDF131 KB
Navodila za uporaboPDF130 KB
Manual de instruccionesPDF137 KB
ManualPDF129 KB
Short instructions, safety information
Brief instructionsPDF282 KB
KurzanleitungPDF283 KB
Tender Texts
Tender textD818 KB
AusschreibungstextD818 KB
Application reports
Application Report - Sand Trap and Preliminary Sedimentation StagePDF448 KB
Applikationsbericht - Sandfang und VorklärungPDF434 KB
Documents
System ManualPDF2706 KB
SystemhandbuchPDF2715 KB

Approvals+Certificates: S1SD-1TI-1U

CertificatesFile TypeFile Size
Canada UL cULLINK---
Europe DEMKO ATEX Category 3 GPDF1876 KB
UL Non-Sparking nA IECEx Certificate of ConformityLINK---
USA ULLINK---
Declaration of Conformity
EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F)PDF468 KB

Associated Products: S1SD-1TI-1U

Matching System Components
Interface for Power Bus, Supply current 3 A, LED status indication, Connection via screw terminalspa
For SC-System, Free of charge, Internet download possiblepa
Isolated USB interface cable, Used with SC-System devices, Configurable via PCpa
Universal DTM host platform, For all DTMs of Pepperl+Fuchs, Approved FDT/DTM technology, Free of charge, Download from Pepperl+Fuchs websitepa
Bus carrier with bus PCB for 35 mm DIN mounting rail, height 7.5 mm, Provides DC supply voltage and the bus connection to all equipped SC-System modules, Standard length 250 mm (9.84 inch), simple to customize to application space, Eliminates daisy-chainspa
Bus carrier with bus PCB for 35 mm DIN mounting rail, height 15 mm, Provides DC supply voltage and the bus connection to all equipped SC-System modules, Standard length 250 mm (9.84 inch), simple to customize to application space, Eliminates daisy-chainspa
Cover for DIN mounting rail, Suitable for Power Bus, Standard length 250 mm (9.84 inch), simple to customize to application space, Packaging unit: 5 piecespa
Fixing of the bus carrier with bus PCB in the DIN mounting rail, Termination of DIN mounting rail, Suitable for Power Bus, Packaging unit: 5 pieces left, 5 pieces rightpa
General Notes Relating to Pepperl+Fuchs Product Information

Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
phone +49 621 776-0

© 2024 All Rights Reserved.

Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.